Live signal viewer#
The live signal viewer is where you watch EEG in real time. You reach it with Stream or View on the device card, from the contact check (see Contact check), or by tapping the Streaming bar. Rec on the device card starts recording without leaving the device list; use View when you want the plot.
← BA MAXI 000 · 32 ch ● 0:32 [camera] [ Stop ]
● 45% · 250 Hz
┌────────────┬──────────────────────────────────────────────┐
│ ▮ ● P8 │ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~│~~~~ │
│ ▮ ● O2 │ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~│~~~~ │
│ … │ │
└────────────┴──────────────────────────────────────────────┘
window 10 s
[ PSD ] [ Accel ]
[ ● Rec ] [ Marker ▾ ] [ 1–40 Hz ] [ Win 10s ] [ Quality ] [ More ]
Top bar#
Control |
What it does |
|---|---|
← Back |
Leaves the viewer. The stream keeps running (and so does any recording) |
Device tabs |
Only with more than one headset streaming: tap a tab or swipe the plot sideways to switch device. Each tab shows the device and worst quality as a coloured dot |
● m:ss |
Recording indicator and elapsed recording time |
Camera icon |
Saves a snapshot PNG of the current view. A brief, nonblocking notice confirms the saved filename or reports an error; it remains visible if you go Back. See Recording |
Stop |
Stops the stream. Hidden while recording — stop the recording first |
Status line#
[state · ] battery% · sample rate [ · N lost] — the leading dot and lost-sample
counter turn red if samples were dropped on the Bluetooth link. The
state word is omitted while everything is normal.
Channel rail#
Starts collapsed in portrait (colour swatch plus quality dot per channel). Tap it to expand, and use the chevron to collapse it again. Expanded, each row shows:
Element |
Meaning |
|---|---|
Colour swatch |
The trace colour for that channel |
Name |
The electrode label. Dimmed when the channel is hidden |
|
Peak-to-peak amplitude over the visible window, refreshed about once a second |
Quality dot |
Green = good, amber = check, red = poor. No dot until the channel has been scored |
Eye icon |
Hide or show that channel |
Long-press a row |
Solo: hides every other channel. Long-press again to restore |
Hidden channels and solo last for the session only; they are not remembered after a restart.
The plot#
One trace per visible channel, stacked, top channel first, with a faint separator per channel.
Electrodes with no contact are drawn dimmed and flattened to their baseline.
Markers appear as amber dashed lines with a label.
Stable mode draws a sweep line at the live edge, like a classic oscilloscope; Flow mode scrolls right to left. Change it in More → Dynamics.
Pinch the plot to change the window length (1–10 s).
The caption under the plot shows the window length (Stable) or the time axis (Flow).
Control dock#
Control |
What it does |
|---|---|
● Rec |
Starts recording; turns red and shows elapsed time. Tap again to stop |
Marker ▾ |
Tap the label to drop a marker with the last-used label; tap the caret or long-press to pick/edit presets |
Filter chip (1–40 Hz / Filter off) |
Opens the filter popup |
Win Ns |
Window length presets: 1 s, 2 s, 5 s, 10 s |
Quality |
Opens Signal quality. The stream keeps running |
More |
Opens the settings sheet |
Filter popup#
Control |
Options |
Default |
|---|---|---|
Filter switch |
Band-pass on/off |
On |
Low cutoff (Hz) |
0.1, 0.5, 1, 2, 4, or custom |
1 |
High cutoff (Hz) |
15, 20, 30, 40, 50, 100, or custom |
40 |
Notch switch |
Mains-hum filter on/off |
On |
Notch frequency |
50 Hz or 60 Hz |
50, or auto-detected from your signal the first time |
Cutoffs are automatically kept inside the range the sample rate allows. Your own notch-frequency choice is remembered and is not overwritten by later detection. Notch auto-detect runs once, the first time a spectrum is computed, and only if you have not chosen a frequency yourself. It looks at every shown channel that has contact and picks 50 or 60 Hz by which peak stands out, so one dead electrode cannot mislead it. If neither stands out it keeps 50 Hz. Custom cutoff fields accept a decimal point or comma. Tap the field’s Done button, or leave the field, to apply the value; it is clamped to the current sample rate.
Important
Filters only change what you see. The band-pass and notch apply to the trace,
spectrum panel and PTP numbers. Recorded files always
contain raw headset data. Signal-quality scores are also computed from raw data.
Settings sheet (More)#
Display
Setting |
Range |
Default |
|---|---|---|
Dynamics |
Stable / Flow |
Stable |
Normalization |
Individual / Common |
Individual |
Window |
1–10 s |
10 s |
Sensitivity |
0–2 |
0 |
Scale |
0.1–3 amplitude multiplier |
1 |
Trace width |
0.5–3 |
1.2 |
Monochrome |
All traces grey instead of colour-coded |
Off |
Output
Setting |
Notes |
|---|---|
Session label (next recording) |
Up to 48 characters. Added to the next recording’s filename/header. Cleared when the app restarts |
LSL outlet |
Greyed out with the caption Not available in this version. LSL streaming is not available in 1.0.0. See Streaming to a computer (LSL) |
Recording format |
BDF (default) or CSV. Cannot be changed while recording |
Reset to default restores display/filter settings. Done closes the sheet.
PSD and Accel panels#
Two chips open one panel at a time:
PSD — median-Welch power spectrum, one line per channel, drawn from filtered display data. Frequency is in hertz; power density is logarithmic (dB), with annotated axes. Brief artifacts are reduced by taking the median of overlapping subwindows. Reads Computing… until the first spectrum is ready.
Accel — accelerometer X, Y and Z in m/s² on headsets that have an accelerometer (MINI, MIDI, MAXI, EXG8, HALO V3). On headsets that also have a gyroscope (EXG8, HALO V3), the same panel adds gyroscope X, Y and Z in degrees per second below it, labelled Accel · m/s² and Gyro · °/s. Each axis is auto-scaled. Shows Waiting for accelerometer… until data arrives.
Landscape#
Rotating gives an immersive plot with overlay controls. The plot follows the selected light/dark instrument palette rather than forcing a different theme.
What keeps running when you leave#
Leaving the viewer does not stop streaming or recording. The root screen shows a return bar while a stream is active. Streaming and recording also continue when you switch apps or lock the screen, as long as iOS keeps the app running; keep the app open when a session must not be interrupted.
See also#
Recording — file formats, markers and snapshots.
Streaming to a computer (LSL) — LSL streaming, not available in this version.
Settings reference — what is remembered across restarts.